PoC: Konfigsnippets

2010-11-22T12:58:54Z

Konfigsnippets

Neue Seite

Als Alternative zu externen ADSL-Modems gibt es die Möglichkeit, '''ADSL-WIC''' (Wan Interface Card) zu verwenden.

== WIC-1ADSL-Varianten ==
'''Achtung, kein ADSL2+!''' — maximal 8 MBit/s downstream, in Deutschland bedeutet das über die Telekom maximal 6 MBit/s, Arcor bietet bis zu 8 MBit/s.

* ADSL over POTS (WIC-1ADSL) für analoge Telefonie wie z. B. in Großbritannien. Äquivalent zum integrierten Modem im Cisco 837-Router. Supports and complies with ANSI T1.413 Issue 2, and ITU G.992.1, Annex A (G.DMT for full-rate ADSL over POTS).'''
* ADSL over ISDN WAN with Dying Gasp support (WIC-1ADSL-I-DG) für den Einsatz bspw. in Deutschland. Äquivalent zum integrierten Modem im Cisco 836-Router. Allows the coexistence of ADSL and ISDN on the same local loop; supports and complies with ITU G.992.1, Annex B (G.DMT for full-rate ADSL over ISDN), ETSI 101-388, and the Deutsche Telekom U-R2 specification.
* Support auf allen Plattformen ausser 3600 (lt. Cisco-Specs).

=== Konfiguration für Deutsche Telekom ADSL ===
Die Konfiguration ist im Endeffekt analog zum integrierten Modem im Cisco 83x. Am Dial-Pool klemmt dann wiederum ein Dialer, der die PPP-Thematik übernimmt.

interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode annexb-ur2
pvc 1/32
pppoe-client dial-pool-number 1

Kartenstatus-Ausgabe (<code>show dsl interface</code>):
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: AnnexB (Deutsche Telekom U-r2)
ITU STD NUM: 0x01 0x01
Vendor ID: 'ALCB' 'BDCM'
Vendor Specific: 0x0000 0x619D
Vendor Country: 0x00 0xB5
Capacity Used: 100% 91%
Noise Margin: 8.0 dB 7.0 dB
Output Power: 18.5 dBm 11.5 dBm
Attenuation: 38.0 dB 29.0 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x11
Interrupts: 2371 (2 spurious)
Activations: 162
Init FW: ASW_init_4_10_9.bin
Operartion FW: ASW_R4_10_9.bin
SW Version: 4.10.9
FW Version: 0x1A04

Interleave Fast Interleave Fast
Speed (kbps): 0 4704 0 672
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 320 0 0
Header Errors: 0 177 1 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin
00: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
10: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
20: 0 A A A A 9 A A A A A A A A A 9
30: 9 9 8 8 8 0 0 0 0 0 0 0 0 0 0 0
40: 6 7 7 8 8 8 8 9 8 9 9 9 9 9 9 9
50: 9 9 9 9 9 9 9 9 A A A A A A A A
60: A A A A A A A A 2 A A A 9 A A A
70: A A A A 9 9 9 9 9 8 8 8 8 7 7 7
80: 7 7 7 6 6 6 6 6 6 6 6 6 6 5 6 6
90: 5 6 6 6 6 6 6 7 7 8 8 9 9 9 9 9
A0: 9 9 9 9 9 9 9 9 9 9 9 8 9 8 9 8
B0: 9 9 9 8 8 9 9 9 8 9 8 9 8 9 8 9
C0: 8 9 8 8 8 8 5 7 7 8 6 7 7 8 8 8
D0: 6 4 7 7 7 6 7 5 7 6 7 5 7 0 0 0
E0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Training log buffer capability is not enabled yet.

== HWIC-1ADSL-Varianten ==
* HWIC-1ADSL supports ADSL-over-POTS (wie z. B. in Großbritannien) (ADSL, ADSL2, and ADSL2+), complying with Annex A of ITU G.992.1, G.992.3, and G.992.5. Äquivalent zum integrierten Modem im Cisco 877-Router.
* HWIC-1ADSLI supports ADSL-over-ISDN (ADSL, ADSL2, and ADSL2+) für den Einsatz bspw. in Deutschland, complying with Annex B of ITU G.992.1, G.992.3, and G.992.5. It also supports and complies with ETSI 101-388 and the Deutsche Telekom U-R2 specification. Äquivalent zum integrierten Modem im Cisco 876-Router.
* HWIC-1ADSL and HWIC-1ADSLI support reach-extended ADSL2, complying with Annex L of ITU G.992.3.
* HWIC-1ADSL and HWIC-1ADSLI comply with ANSI T1.413 issue 2.
* HWIC-1ADSL and HWIC-1ADSLI support ATM AAL5 services and applications, ATM class of service (constant bit rate [CBR], variable bit rate-nonreal time [VBR-nrt], variable bit rate-real time [VBR-rt], and unspecified bit rate [UBR]), and up to 23 virtual circuits on an HWIC in Cisco routers.
* HWIC-1ADSL and HWIC-1ADSLI provide ATM traffic management and Quality of Service (QoS) features to enable service providers to manage their core ATM network infrastructures.
* HWIC-1ADSL and HWIC-1ADSLI support [http://de.wikipedia.org/wiki/Dying_Gasp Dying Gasp] functionality.

=== Konfiguration für Deutsche Telekom ADSL ===
Die Konfiguration ist im Endeffekt analog zum integrierten Modem im Cisco 87x. Am Dial-Pool klemmt dann wiederum ein Dialer, der die PPP-Thematik übernimmt.

interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
pvc 1/32
pppoe-client dial-pool-number 1

Kartenstatus-Ausgabe (<code>show dsl interface</code>):
ATM0
Alcatel 20190 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.5 (ADSL2+) Annex B
ITU STD NUM: 0x03 0x1
Chip Vendor ID: 'STMI' 'IFTN'
Chip Vendor Specific: 0x0000 0x711C
Chip Vendor Country: 0x0F 0xB5
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x0000 0x0000
Modem Vendor Country: 0xB5 0x00
Serial Number Near: FHK1232244U
Serial Number Far:
Modem VerChip ID: C196 (0)
DFE BOM: DFE3.0 Annex B (2)
Capacity Used: 98% 92%
Noise Margin: 6.5 dB 6.0 dB
Output Power: 16.5 dBm 12.5 dBm
Attenuation: 15.0 dB 7.0 dB
FEC ES Errors: 0 0
ES Errors: 1 0
SES Errors: 1 0
LOSES Errors: 1 0
UES Errors: 0 6
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0x9A
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x00 (UR2)
Interrupts: 4116 (0 spurious)
PHY Access Err: 0
Activations: 1
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: init_AMR-4.0.003.bin
Operation FW: AMR-4.0.003.bin
FW Source: external
FW Version: 4.0.3

DS Channel1 DS Channel0 US Channel1 US Channel0
Speed (kbps): 0 17696 0 1064
Cells: 0 26148061 0 2405471703
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 5621 0 0
Header Errors: 0 4362 0 0
Total BER: 0E-0 1526E-9
Leakage Average BER: 0E-0 2476E-11
Interleave Delay: 0 19 0 3
ATU-R (DS) ATU-C (US)
Bitswap: enabled enabled
Bitswap success: 0 0
Bitswap failure: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin
000: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
010: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
020: 0 8 8 9 A A B B B C C C C C C C
030: C C B B B B B A A 9 9 8 0 0 4 5
040: 7 7 9 9 A B B B C C C C C C C C
050: C C C C C C C C C C C C C C C D
060: B C C C C C C C C C C C C C C C
070: C C C D D 2 C C C C C C C C C C
080: C C C C C C C C C C C C C C B C
090: C C C C C C C C C C C C C B C B
0A0: B B B B B B B B B B B B B B B B
0B0: B B B B B B B B B B B B B B B B
0C0: B B B B B B B B B B B B B B B B
0D0: B B B B B B B B B B B B B B B B
0E0: B B B B B B A A B A B B B A A B
0F0: A B A A A A A A B B A A A A B A
100: B A B B B B B B B B B B B B B B
110: B B B B B B B B B B B B B B B B
120: B B B B B B B B A B B B B B B B
130: B B B B B B B B B B B B B B B B
140: B B B B B B B B B B B B B B B B
150: B B B B B B B B B B B B B B B B
160: B A A A A B A A A A A A A A A A
170: A A A A A A A A A A A A A A A A
180: A A A A A A A A A A A A A 9 9 9
190: 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
1A0: 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
1B0: 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
1C0: 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 8
1D0: 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8
1E0: 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8
1F0: 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8

DSL: Training log buffer capability is not enabled

== Siehe auch ==
* [[SDSL-WIC für Cisco-Router]]

== Weblinks ==
* [http://www.cisco.com/en/US/docs/ios/12_2/12_2z/12_2zj/feature/guide/adslwan.html WIC-1ADSL bei Cisco]
* [http://www.cisco.com/en/US/docs/ios/12_4t/12_4t4/dsl_hwic.html HWIC-1ADSL bei Cisco]
* [http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/dsl_hwic.html Hardware Installation Guide for WAN Interface Cards]
* [http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/oview_ic.html#wp1129978 Platform Support for Cisco Interface Cards]
* [http://www.cisco.com/en/US/docs/ios/bbdsl/configuration/guide/bba_1pt_adsl_wan_ps6350_TSD_Products_Configuration_Guide_Chapter.html Cisco IOS Broadband Access Aggregation and DSL Configuration Guide, Release 12.4], Abschnitt über WIC-1ADSL.

[[Kategorie:Cisco]]

ADSL-WIC für Cisco-Router - Versionsgeschichte

PoC: Konfigsnippets