ULTRIX 3 VAX

Aus Knowledgebase
Version vom 13. Mai 2019, 13:10 Uhr von Luna (Diskussion | Beiträge) (Die Seite wurde neu angelegt: „restoring Ultrix 3.1 on a MicroVAX 3100 copy image to harddisk using dd boot in single user mode: boot/r5:2 dkb100 fsck edit /etc/fstab edit /etc/passwd edit…“)
(Unterschied) ← Nächstältere Version | Aktuelle Version (Unterschied) | Nächstjüngere Version → (Unterschied)
Zur Navigation springen Zur Suche springen

restoring Ultrix 3.1 on a MicroVAX 3100

copy image to harddisk using dd boot in single user mode: boot/r5:2 dkb100

fsck edit /etc/fstab edit /etc/passwd edit /etc/group edit /etc/ttys edit /etc/hosts edit /etc/resolv.conf edit /etc/rc.local

build new kernel to recognize additional disks. doconfig, then choose to edit config file with vi. add: disk rz2 at scsi0 drive 2

After building a new kernel, doconfig changes /etc/rc.local and uses the ident name of the kernel configuration as the new hostname. This might break things. Check and reset to a proper hostname.

pluto(root): <conf> 49 > cat /etc/fstab /dev/rz9a:/:rw:49:1:ufs:: /dev/rz9g:/usr:rw:49:2:ufs:: /dev/rz9h:/usr/local:rw:98:3:ufs:: /dev/rz2a:/home:rw:98:4:ufs::

pluto(root): <conf> 51 > df Filesystem Total kbytes kbytes % node kbytes used free used Mounted on /dev/rz9a 19183 7323 9942 42% / /dev/rz9g 239663 129235 86462 60% /usr /dev/rz9h 233247 46743 163180 22% /usr/local /dev/rz2a 191958 72583 100180 42% /home

The largest small 3.5" SCSI disk that is know by ULTRIX 3.1 is the RZ23. But we can just add the RZ24:

rz24|RZ24|DEC RZ24 Winchester:\

       :ty=winchester:ns#38:nt#8:nc#1348:\
       :pa#32768:ba#8192:fa#1024:\
       :pb#131072:bb#4096:fb#1024:\
       :pc#409792:bc#8192:fc#1024:\
       :pd#81984:bd#8192:fd#1024:\
       :pe#81984:be#8192:fe#1024:\
       :pf#81984:bf#8192:ff#1024:\
       :pg#245952:bg#8192:fg#1024:

This would likely work for other disks, but ULTRIX 3 very likely cannot use disks larger than 1GB. /etc/chpt works as known from ULTRIX 4.


pluto(root): <conf> 50 > cat /etc/ttys

  1. "@(#)ttys 4.1 (ULTRIX) 11/23/87"
  2. name getty type status comments
  3. console "/etc/getty e" dw3 on secure # console terminal

console "/etc/getty std.9600" vt100 on secure # console terminal tty00 "/etc/getty std.9600" vt100 on nomodem secure # direct connect tty tty01 "/etc/getty std.9600" vt100 off nomodem secure # direct connect tty tty02 "/etc/getty std.9600" vt100 off nomodem secure # direct connect tty tty03 "/etc/getty std.9600" vt100 off nomodem secure # direct connect tty tty04 "/etc/getty std.9600" vt100 off nomodem secure # direct connect tty tty05 "/etc/getty std.9600" vt100 off nomodem secure # direct connect tty tty06 "/etc/getty std.9600" vt100 off nomodem secure # direct connect tty tty07 "/etc/getty std.9600" vt100 off nomodem secure # direct connect tty ttyp0 none network secure ttyp1 none network secure ttyp2 none network secure ttyp3 none network secure ttyp4 none network secure ttyp5 none network secure ttyp6 none network secure ttyp7 none network secure ttyp8 none network secure ttyp9 none network secure ttypa none network secure ttypb none network secure ttypc none network secure ttypd none network secure ttype none network secure ttypf none network secure ttyq0 none network secure ttyq1 none network secure ttyq2 none network secure ttyq3 none network secure ttyq4 none network secure ttyq5 none network secure ttyq6 none network secure ttyq7 none network secure ttyq8 none network secure ttyq9 none network secure ttyqa none network secure ttyqb none network secure ttyqc none network secure ttyqd none network secure ttyqe none network secure ttyqf none network secure

  1. ttyv0 "/usr/bin/xterm -L -sb -rv -geometry =80x24+195+275 -d unix:0" xterm on secure window="/usr/bin/Xqdsg -fd 75 :0"
    0 "/usr/bin/login -P /usr/bin/Xprompter -C /usr/bin/dxsession" none on secure window="/usr/bin/Xqdsg -fd 75 -bp #000080 c 70"
  2. xcons "/usr/bin/xcons 10 ttyv0" none on nomodem

Y2K:

set the date to 9912312359.59

then continue to set the date to 12312359.59 in steps until you reach the current year.


setld -l /dev/rmt0h


build GNU stuff:

gcc-1.42: sh configure vax make make stage1 make CC=stage1/gcc CFLAGS="-g -O -Bstage1/"

do a make install. Trust this stage.


make stage2 make CC=stage2/gcc CFLAGS="-g -O -Bstage2/"


make CC="stage1/xgcc -Bstage1/" CFLAGS="-g -O" make stage2 make CC="stage2/xgcc -Bstage2/" CFLAGS="-g -O" make compare make install


flex-2.5.4a scan.c want to include stdlib.h, which does not exists.

make check fails, because we have edited scan.c Trust and install anyway...

Ultrix 3.0: flexdef.h: add: typedef int size_t;


gawk-1.01

sed-1.18 bison-1.25

Ultrix 3.1: edit /usr/local/lib/gcc-include/stddef.h and remove definition of size_t Ultrix defines size_t in <sys/types.h> as "typedef int size_t;"

Ultrix 3.0 works fine.


make-3.75 m4-1.4 bash-1.14.7

gcc-2.3.3

ultrix 3 doesn't know about atexit().

  1. undef HAVE_ATEXIT before building gcc.

configure as vax-dec-ultrix3.1 then do a make bootstrap gcc will use the host cc to build the first stage. This works. You can also edit the Makefile and use gcc to build the first stage: CC = gcc


sed-3.02 sed/utils.h:

  1. include <sys/types.h>


gzip-1.2.4a

gawk-3.0.6 --disable-nls protos.h: uncomment: /* extern SPRINTF_RET sprintf P((char *, const char *, ...)); */ needs link with -lm

copy install-sh from gawk to /usr/local/bin/install

there is something in sys/types.h that gcc-2.3.3 cannot compile. Fix the "volatile" on line 80 ff and copy the custom header to the gcc include directory.

grep-2.3

binutils-2.7 binutils/arlex.c: remove includes of stdlib.h ld/ldlex.c: remove includes of stdlib.h

On Ultrix 3.0: if there are any "size_t undeclared" error, include <sys/types.h>

make install will fail. Copy as to /usr/local/bin/gas and ld to /usr/local/bin/gnuld.


gcc-2.7.2.3: incorrectly includes stdlib.h in ../gcc-2.7.2.3/cpplib.c on line 73.

--with-as=/usr/local/bin/gas --with-gnu-as --with-ld=/usr/local/bin/gnuld --with-gnu-ld --enable-languages=c,c++,f77

change Makefile: edit CC = cc to CC = gcc. stage1 gcc cannot be build with VAX cc anymore.

Ultrix 3.0: /home/compile/gcc-2.7.2.3/xgcc -B/home/compile/gcc-2.7.2.3/ -O -fgnu-runtime \ -c -DIN_GCC -O -g -I./include -I. -I.. -I/home/compile/gcc-2.7.2.3 -I/home/compile/gcc-2.7.2.3/config NXConstStr.m Assembler: "/usr/tmp/cca25075.s", line 182: Invalid type in .stabs make[2]: *** [NXConstStr.o] Error 1 make[2]: Leaving directory `/home/compile/gcc-2.7.2.3/objc' make[1]: *** [libobjc.a] Error 2 make[1]: Leaving directory `/home/compile/gcc-2.7.2.3' make: *** [bootstrap] Error 2

retry withouth gnu as: also fails... Foor some reason, ULtrix 3 and 3.1 won't build gcc-2.7.2.3.

gcc-2.5.8: --with-as=/usr/local/bin/gas --with-gnu-as --with-ld=/usr/local/bin/gnuld --with-gnu-ld --enable-languages=c change Makefile: edit CC = cc to CC = gcc

gcc-2.6.3: --with-as=/usr/local/bin/gas --with-gnu-as --with-ld=/usr/local/bin/gnuld --with-gnu-ld --enable-languages=c change Makefile: edit CC = cc to CC = gcc

fails to build objc in stage1. edit Makefile and remove objc from LANG


make-3.79.1: glob/fnmatch.c:

  1. include <sys/types.h>
  2. define NULL 0

do not strip the make binary. this breaks make.

function.c and job.c:

  1. ifndef remove
  2. define remove unlink
  3. endif

libiconv-1.9.2: needs some #include <sys/types.h> in files that use size_t.


patch-2.5.9 dirname.h:

  1. include <sys/types.h>

config.h

  1. define HAVE_STRUCT_UTIMBUF 1


jpeg-6b

tar-1.11.8



tin-2.4.4: ./configure --enable-nntp-only --with-domain=pcde.inka.de --with-nntp-default-server=news.akk.org --disable-nls --with-editor=/usr/local/bin/vim --enable-broken-system-fix mips-dec-ultrix3.1

pcre/dftables.c: Ultrix fopen() doesn't understand argument "wb". Change to "w+"

add to pcre/pcre_globals.c:

  1. include <sys/types.h>

extern void *malloc(size_t); extern void *realloc(void *, size_t); extern void free(void *);